There are many precautions for the operation of broken bridge aluminum door and window equipment. Before we use the broken bridge aluminum door and window equipment, we need to do the basic power and air source inspection work, and then set the material placement position, feeding speed, etc. Only later can you start processing doors and windows. Precautions for the operation of broken bridge aluminum doors and windows 1. First, adjust the position of the side pressure cylinder. First put the profile to be processed on the workbench, adjust the indenter of the equipment to the middle position of the profile, and then lock the cylinder bracket. 2. Need to adjust the feeding speed of the saw blade for the broken aluminum door and window frame equipment. In the process of testing the equipment, if you find that the feeding speed of the saw blade is too fast or too slow, you can adjust the speed control valve of the feeding cylinder of the bridge-broken aluminum door and window frame equipment to obtain a suitable feeding speed. Adjustment of aluminum alloy profile precision cutting saw (1) Adjust the position of the compression cylinder. Place the aluminum alloy profile on the workbench of the aluminum door and window equipment, adjust the compression cylinders of the two saw heads to a position suitable for compressing the workpiece, and then fix it Tighten the cylinder. (2) Adjust the feed speed of the saw blade. First, test the machine with the default feed speed of the cutting saw. During the test, if the feed speed of the saw blade is not suitable, you can adjust the speed control joint of the working oil cylinder to increase or decrease the feed speed to obtain the required feed speed. (3) Adjust the cutting angle of the precision cutting saw for aluminum alloy profiles. The precision cutting saw for aluminum alloy profiles was adjusted according to the above items, and the trial operation was carried out for 30 minutes after meeting the requirements. (4) Adjust the cutting angle of the equipment to 90 (the extended part of the saw blade is perpendicular to the table). The precision cutting saw for aluminum alloy profiles has been adjusted and passed the inspection before leaving the factory. Aluminum alloy profiles can be sawed directly here, and a 90-degree saw can be tested for compliance with the requirements, with an error of 10'. If it does not meet the requirements, you can adjust the bolts on the limit baffle. Then repeat the sawing measurement to meet the requirements. After that, pay attention to tighten the nut on the cutting saw. (5) Adjust the cutting angle of the equipment to 45 (when the angle between the extension of the saw blade and the work surface is 45, set it to 45) Loosen the locking handle on the work table, and ventilate the swing cylinder. Lock the handle when it reaches 45 degrees. After sawing, check whether the profile meets the requirements (the error is 10'). If it does not meet the requirements, adjust the limit screw on the limit baffle, repeat sawing and measurement, to meet the requirements. Then tighten the nut on the screw and tighten the lock handle. (6) After adjusting the cutting length angle of the profile, the cutting length of the aluminum alloy profile should be adjusted. Pull the handle to drive the right saw head to move to an accurate position along the circular guide rail (see the scale pointer). The length indicated by the scale is the length of the short side of the aluminum alloy profile. After cutting, if the length of the cut profile deviates from the required length, it should be fine-tuned. When making fine adjustments, tighten the brake adjuster and turn the fine adjuster to the desired size. Operation of precision cutting saw for aluminum alloy profiles (1) First of all, everyone should be familiar with the functions of the buttons on the operation panel. (2) After adjusting the angle and workpiece length, press the saw head start button. After the saw head motor runs stably, install the profile and press the clamp and saw stop buttons at the same time. In special cases, press the emergency stop button. When the saw head selection switch is set to the left or right position, the left and right saw heads can work independently. If set in the double position, the left and right saw heads can work at the same time. After the work is over, turn off the main power supply. What are the operating methods of broken bridge aluminum doors and windows? Now, many high-rise buildings have risen from the ground. Now that the high-rise building has been built, it needs to be renovated and windows need to be installed. Many people now choose to use broken aluminum doors and windows when installing windows because they are relatively more environmentally friendly. Formally because of this, many manufacturers of broken bridge aluminum doors and windows have sprung up. So, what problems should we pay attention to when using broken bridge aluminum doors and windows equipment? Operation method of broken bridge aluminum doors and windows equipment 1. Air source. Because the pressed materials of the broken bridge aluminum doors and windows equipment are compressed by gas cylinders, ensuring sufficient air source is a prerequisite for the efficient use of the equipment. 2. Equipment. Because there are many types of broken bridge aluminum doors and windows equipment, each equipment may have several machines. It is particularly important to check door and window equipment, such as the air pipe plug of the cutting saw, the in and out speed of the saw blade, and the left and right working status of the saw head. 3. The feeding should not be too fast. For automatic feeding, the hand wheel on the worktable must be opened, and the feeding speed is not allowed to be changed suddenly. The limit gear should be adjusted first. 4. When disassembling the end milling machine, the workbench needs to be padded with wooden boards, and it is strictly forbidden to hold the cutter head by hand. Do not blow directly with your hands or mouth to remove iron filings. If there is any abnormal situation, stop the machine immediately and ask relevant personnel to check. 5. In terms of power supply, since the commonly used voltage of bridge-broken aluminum doors and windows equipment is 380V, you must pay attention to the connection of live and neutral wires when wiring. 6. When cutting, the head and hands should not be close to the milling surface. When removing the workpiece, the cutter needs to be removed. It is strictly forbidden to touch or wipe the rotating tools and transmission parts of the machine tool with cotton yarn, and it is strictly forbidden to transfer or remove the tools and other items through the rotating parts of the machine tool. Nowadays, the competition in the aluminium processing machine
industry of broken bridge aluminum doors and windows is fierce. Every manufacturer is constantly improving its own production technology, and every work procedure is very rigorous. Since the establishment of our company, with professional technical team and strong processing strength, we have provided users with high-quality door and window equipment and perfect technical solutions, and strictly abide by the ISO9001: 2000 international quality system standards for product design and production. If necessary, please contact us. 144
Whenever you grab your remote and turn on the TV, there are numerous ads promoting punching machine design and offering for aluminum panel bending machine extracts, which are said to boost cnc grinding machine.
Growing revenue is a common goal for many businesses. We want to be sure kingtool aluminium machinery include leaders from the marketing, sales and production departments to help make certain that the goals we choose are appropriate and have strong support.
The personal cnc machine ACP GROOVING MACHINE is an all-servo system capable of storing hundreds of punching machine for sale process parameters to provide custom metal cnc machine profiles for each precision cnc machining type and aluminum cutter machine configuration.