Installation method of processing equipment for broken aluminum doors and windows

by:kingtool aluminium machinery     2021-09-08
Broken bridge aluminum doors and windows processing equipment is a very efficient 'combined equipment, But in this one, how to install is a more complicated problem. From a small point, we need to make the equipment have a connection sequence, and at a larger point, we need to make the equipment installation better, so as to promote production efficiency and pass rate . Door and window processing equipment installation method Door and window processing equipment has the characteristics of thermal expansion and cold contraction, so the seal between the door and window processing equipment and the wall interface is a dynamic seal. Under normal circumstances, the expansion and contraction value of door and window aluminium processing machine can reach more than 10 mm. In order to ensure that the door and window processing equipment can expand and contract freely after installation, the cavity between the door and window and the wall should be filled with elastic materials. If only hard cement mortar is used for sealing, this requirement cannot be met, and due to the high thermal conductivity of the mortar, it will shrink and crack over time, further affecting the air tightness, water tightness and sound insulation of doors and windows. In addition, the advantages of elastic materials such as earthquake resistance, crack resistance, waterproofing, fire resistance, heat preservation, and strong adhesion are unmatched by hard cement mortar. At present, the elastic materials used include cold-proof felt strips, foamed plastics, silicone foamed sealants and polyurethane foaming agents, etc. The foaming agents are widely used. Three check points before installation of broken bridge aluminum door and window equipment 1. In terms of power supply, because the commonly used voltage of broken bridge aluminum door and window equipment is 380V, you must pay attention to the connection of live and neutral wires when wiring. Generally speaking, Door and window equipment manufacturers will give a wink. The live line is black or blue, and the neutral line is red (each manufacturer depends on its own situation). If the live line is reversed, just change the two wires at both ends of the live line. That's it. 2. Air source. Since the pressing material of the broken bridge aluminum door and window equipment is compressed by gas cylinders, ensuring a sufficient air source is a prerequisite for improving the efficiency of the equipment. If the air pressure is not reached, the saw blade in and out of the double-head cutting saw for broken bridge aluminum profile will be affected, and the processing effect will be affected accordingly. Generally speaking, a set of broken bridge aluminum doors and windows equipment should ensure that the air pressure can reach 8 pressures and the air flow rate can reach 0.3. If there are too many equipments, only relying on air pumps is not enough. It is also necessary to add some new equipment to the equipment to ensure the processing effect of the broken aluminum doors and windows. 3. Equipment. Because there are many types of broken bridge aluminum doors and windows equipment, each equipment may have several types of machines. It is particularly important to check the door and window equipment, such as the air pipe plug of the cutting saw, the speed of the saw blade, the left and right working status of the saw head, and so on. Precautions for the installation of broken bridge aluminum doors and windows Because the common voltage of broken bridge aluminum doors and windows equipment is 380V, we must pay attention to the connection of live and neutral wires when wiring. Generally speaking, the live wire is black or blue, and the zero wire is red. If the live line is reversed, just change two at both ends of the live line. Since the pressing material of the broken aluminum door and window equipment is compressed by gas cylinders, ensuring sufficient air supply is a prerequisite for improving the efficiency of the equipment. If the air pressure cannot be reached, the in and out of the saw blade of the double-head cutting saw for broken bridge aluminum profile will be affected to a certain extent, and the corresponding processing effect will also be affected to a certain extent. A set of broken bridge aluminum doors and windows equipment should ensure that the air pressure can reach 8 pressures and the air flow rate can reach 0.3. If there are too many equipment, it is not enough to rely on air pumps. Generally, one or two air tanks are required. The above is about the installation precautions of the broken bridge aluminum door and window processing equipment. From the power supply to the installation skills, and specific parts, we need to install carefully to ensure the normal operation of the equipment. 99
Owing to its cutting cnc machine and precision cnc machining benefits, has become a buzzword in the cnc machine woodworking market.
Always do our research, follow the rules and plans ahead for additional expenses. Expanding is the goal of Kingtool Aluminum Doors and Windows Machinery Co., Ltd.; expanding properly is the goal of the wise business.
Even chinese curtain wall are being made fine with advanced equipment.
Obviously, financial return is important in manufacturing aluminum cnc machine, but I think that's not enough. I think many customers want to support something they really believe in.
The unique connections between trimming machinemanufacturing and customers happen when you find ways to relate on a more personal and engaging level that goes beyond a product.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...