Daily maintenance of aluminum alloy doors and windows equipment

by:kingtool aluminium machinery     2021-10-06
The daily maintenance work of aluminum alloy doors and windows equipment is very complicated, but we need to do it very carefully to extend the service life of the equipment, and increase production efficiency and precision during processing to prevent excessive processing errors of aluminum profiles. Daily maintenance of aluminum alloy doors and windows equipment, check mechanical parts and fasteners to prevent loosening. Every conveying part must be regularly lubricated, and the movable head rail must be regularly lubricated every week. Keep a certain amount of oil in the oil cup, change the circulating water in the water tank every day, clean the water tank regularly every week, check the nozzle regularly, and clean up if it is blocked. The working surfaces and jaws of the vise, upper and lower tongs should be kept clean and oil-free, and should be scrubbed every shift. When the machine tool is not in use, clean it first, and then complete the anti-rust work of the circular guide rail and other moving parts. The electric control box should be kept clean, cleaned frequently, and dried with an air gun. Regularly overhaul the on-site power supply system of the equipment, and check the relationship between the phase line and the neutral line of the power supply system. Check the high-pressure hose regularly. Long-term use of high-pressure hose will cause aging and damage everywhere, and the compressive strength of the hose will also decrease. The air source processor needs to be cleaned regularly, and the pressure gauge needs to be properly adjusted. The storage environment of the machine should be kept dry and free from moisture and corrosive gases to avoid damage to the machine. Always check whether the shower equipment needs to add coolant, check the mechanical screws and fasteners, to prevent loosening and affect the use, especially the travel switch behind the two ends. The machine should be kept clean. After each shift, the chips should be cleaned up in time, and the dust on the surface of the guide rail and the machine should be wiped. The exposed surface of the disc guide should be lubricated and coated with a uniform coating. Equipment that has not been used for a long time should be cleaned and maintained accordingly, and a protective cover can be properly covered. Regular maintenance of aluminum alloy aluminium processing machine can not only reduce hidden dangers, but also extend the service life of the equipment and improve work efficiency. In fact, it has important meaning. Maintenance of milling equipment 1. Clean up the aluminum (wood) dust on the equipment, especially the transmission parts and moving parts of the equipment (such as guide rails, oil cylinders, work panels, etc.) after the end of daily work. 2. Regularly check the screws of each part of the equipment to prevent loosening, resulting in accuracy errors and safety accidents. 3. Regularly wipe the diluted lubricating oil (such as linear guide) for each drive shaft of the equipment. 4. Use oil-based cutting fluid for aluminum machine, and appropriately reduce the proportion of water added. 5. Before starting work every day, check whether the air circuit of the equipment and the solenoid valve body are icy, and use the equipment after ensuring that the air circuit is unblocked. In order to avoid freezing in the air path, the air compressor must be waterproofed and the filter element must be replaced every day. 6. Check whether the power switch is normal and whether the wire is aging every day. If there is any problem, replace it immediately. 7. Be careful when handling aluminum profiles, wood, etc., to prevent collisions, which may cause equipment damage and errors. 8. It is strictly forbidden to operate the equipment with gloves, and it is strictly forbidden to wear gloves. It is strictly forbidden to wear scarves and similar clothing to prevent safety accidents. Maintenance of assembly equipment 1. Clean up the aluminum (wood) dust and silt in the area of u200bu200bthe equipment table. 2. Add lubricating oil to all moving parts of the countertop. 3. Try to inject 32# hydraulic oil into the hydraulic oil of the angle steel assembly machine. 4. Before starting work every day, check whether the air circuit of the equipment and the solenoid valve body are icy, and use the equipment after ensuring that the air circuit is unblocked. In order to avoid freezing in the air path, the air compressor must be waterproofed and the filter element must be replaced every day. 5. Regularly check the screws of each part of the equipment to prevent loosening, resulting in accuracy errors and safety accidents. 6. Check whether the power switch is normal and whether the wire is aging every day. If there is any problem, replace it immediately. 7. Be careful when handling aluminum profiles, wood, etc., to prevent collisions, which may cause equipment damage and errors. 8. It is strictly forbidden to operate the equipment with gloves, and it is strictly forbidden to wear gloves. It is strictly forbidden to wear scarves and similar clothing to prevent safety accidents. 233
Kingtool Aluminum Doors and Windows Machinery Co., Ltd.'s products comply fully with all compatible producing regulations.
If you would like to learn more about , be sure to visit Kingtool Aluminium Machinery for more information!
Latest technology and manufacturing equipment has improved the quality of chinese curtain wall.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...